求助，advisor安装问题

缓缓归矣

安装后，点击continue后，grade options点不动，[SimSetupFig:grade_pushbutton_Callback] Error!
Cannot find an exact (case-sensitive) match for 'GradeFig'

The closest match is: gradefig
in e:\advisor\gui\gradefig.m

> In SimSetupFig>grade_pushbutton_Callback at 1025
  In SimSetupFig at 374
点击run后又出现Warning: The MaskInitialization string of block 'BD_PAR/drive cycle <cyc>/repeated cycle grade vs.
distance' contains usage of mask variables by reference (' @1') instead of by variable name. Support
for this usage will be removed in a future release
  In gui_run_simulation at 82
  In gui_run at 404
  In SimSetupFig>run_pushbutton_Callback at 1344
  In SimSetupFig at 374
Warning: The MaskInitialization string of block 'BD_PAR/drive cycle <cyc>/repeated cycle speed vs.
time' contains usage of mask variables by reference (' @1 @1 @2') instead of by variable name. Support
for this usage will be removed in a future release
  In gui_run_simulation at 82
  In gui_run at 404
  In SimSetupFig>run_pushbutton_Callback at 1344
  In SimSetupFig at 374
Warning: The MaskInitialization string of block 'BD_PAR/drive cycle <cyc>/repeated cycle vehicle cargo
mass vs. distance' contains usage of mask variables by reference (' @1') instead of by variable name.
Support for this usage will be removed in a future release
  In gui_run_simulation at 82
  In gui_run at 404
  In SimSetupFig>run_pushbutton_Callback at 1344
  In SimSetupFig at 374
Warning: The MaskInitialization string of block 'BD_PAR/drive cycle <cyc>/super-smooth, no-lag trace'
contains usage of mask variables by reference (' @1') instead of by variable name. Support for this
usage will be removed in a future release
  In gui_run_simulation at 82
  In gui_run at 404
  In SimSetupFig>run_pushbutton_Callback at 1344
  In SimSetupFig at 374
Warning: The MaskInitialization string of block 'BD_PAR/par <vc> config/<vc> par/engine on (parallel
hybrid)/key_on' contains usage of mask variables by reference (' @1 @1 @2') instead of by variable
name. Support for this usage will be removed in a future release
  In gui_run_simulation at 82
  In gui_run at 404
  In SimSetupFig>run_pushbutton_Callback at 1344
  In SimSetupFig at 374
Warning: The specified delay time for 'BD_PAR/par <vc> config/<vc> par/parallel clutch
control/Transport Delay' is smaller than the step size of the fixed-step solver. This may cause
simulation results to be inaccurate. Consider decreasing the step size of the solver to improve
accuracy
  In gui_run_simulation at 82
  In gui_run at 404
  In SimSetupFig>run_pushbutton_Callback at 1344
  In SimSetupFig at 374
Warning: Outport 'BD_PAR/energy storage <ess>/ess config/energy storage <ess>/ess
tmp/Tair,ave/Tair_ave' and 'BD_PAR/energy storage <ess>/ess config/energy storage <ess>/ess tmp/Tair'
which are driven by the same signal must have the same setting for the "Output when disabled" parameter
  In gui_run_simulation at 82
  In gui_run at 404
  In SimSetupFig>run_pushbutton_Callback at 1344
  In SimSetupFig at 374
[SimSetupFig:run_pushbutton_Callback] Error!
Error using gui_run_simulation (line 82)
Error due to multiple causes.
> In SimSetupFig>run_pushbutton_Callback at 1351
  In SimSetupFig at 374
>>
求大神指点啊